How to disinfect surfaces after washing with detergent

A professional step-by-step guide with the right product for the type of soil, the equipment you need and the safety precautions. Works for: Washable surfaces that are already clean.

Quick answer: To disinfect surfaces after washing with detergent, use chlorinated disinfectant for food-contact surfaces; Peracetic acid disinfectant; Quaternary ammonium disinfectant; main steps: make sure the surface is clean and rinsed; apply disinfectant over the whole surface; let it work for 10 minutes; rinse if the label says so.
AreaFood handling areas
ContaminationHigh
Dwell time10 minutes of contact
DifficultyMedium
Estimated time0.5 min per m²

What you'll need

  • Product (by type): Chlorinated disinfectant for food-contact surfaces; Peracetic acid disinfectant; Quaternary ammonium disinfectant
  • Reference dilution: Chlorinated disinfectant for food-contact surfaces: pH 12–14; up to 1:400; Peracetic acid disinfectant: pH 0–2; per the label; Quaternary ammonium disinfectant: pH 8.5–10.5; up to 1:10. Always check the label of the product you use.
  • Equipment: Sprayer or foam generator; squeegee; counter squeegee; microfiber mop
  • Protection (PPE): Waterproof PVC apron; rubber chemical gloves; safety goggles; waterproof safety boots; hair net; uniform

Step by step

How to disinfect surfaces after washing with detergent: The numbers in the picture match the steps below.
The numbers in the picture match the steps below.
  1. Make sure the surface is clean and rinsed.
  2. Apply disinfectant over the whole surface.
  3. Let it work for 10 minutes.
  4. Rinse if the label says so.
  5. Dry the ceiling with a mop, counters with a counter squeegee and the floor with a squeegee.

The balance of this job (Sinner's Circle)

Every clean combines chemistry, mechanical action, temperature and time. Here's how much each one counts in this task — learn the method.

ChemistryHigh — disinfectant at the label concentration
Mechanical actionLow — just apply
TemperatureLow — room temperature
TimeHigh — 10 minutes of contact
Missing something? Here's how to compensate: Disinfectant doesn't work on a dirty surface — if there is still visible dirt, go back and clean first. Never cut the contact time short.

Safety tips and common mistakes

Never mix different disinfectants. Always follow the label on rinsing food-contact surfaces.
When to call a professional: Outbreak, contamination or when a lab report is required.

Frequently asked questions

What product should I use to disinfect surfaces after washing with detergent?

Chlorinated disinfectant for food-contact surfaces; Peracetic acid disinfectant; Quaternary ammonium disinfectant. Reference dilution: Chlorinated disinfectant for food-contact surfaces: pH 12–14; up to 1:400; Peracetic acid disinfectant: pH 0–2; per the label; Quaternary ammonium disinfectant: pH 8.5–10.5; up to 1:10. Always check the label of the product you use.

How long should the product sit?

10 minutes of contact.

What protective equipment (PPE) should I wear?

Waterproof PVC apron; rubber chemical gloves; safety goggles; waterproof safety boots; hair net; uniform.

What equipment and supplies do I need?

Sprayer or foam generator; squeegee; counter squeegee; microfiber mop.

What precautions and common mistakes should I know about?

Never mix different disinfectants. Always follow the label on rinsing food-contact surfaces.

What if I don't have everything?

Disinfectant doesn't work on a dirty surface — if there is still visible dirt, go back and clean first. Never cut the contact time short.

How long does it take to disinfect surfaces after washing with detergent?

0.5 min per m².

When should I call a professional?

Outbreak, contamination or when a lab report is required.

Technical content written by MiLimpa based on professional cleaning methods (Supermarket cleaning video training). Initial version, under technical review. Always follow the label and safety data sheet of the product you use.